Warm-white light performance of Dy3+, Eu3+: NaLa(WO4)2 phosphors excited with a 450-nm LED

Dy³⁺, Eu³⁺: NaLa(WO₄)₂ phosphors are successfully synthesized through the solid-state reaction technique. The phase-structure and morphology are measured via X-ray diffraction and energy dispersive spectrometry. The concentrations of Dy³⁺, Eu³⁺, La³⁺, and W⁶⁺ are measured via ICP. The absorption and excited spectra are presented, which indicate that a blue band ranging from 430 to 480 nm is suitable for excitation. Using a commercial blue LED with a wavelength of 450 nm as the excitation light source, emission spectra for samples with varying dopant concentration ratios of Dy³⁺ to Eu³⁺ are obtained, which show good tunable yellow and red emission. For the purpose of investigating white LED performance, CIE spectra and a white light photo are also presented. The results reveal that varying the dopant concentration ratio of Dy³⁺ to Eu³⁺ plays a key role in the warm-white performance. With increasing concentration of Eu³⁺, the correlated color temperature decreases from 4069 to 3172 K, which indicates good warm-white performance.     

剂油比对煤焦油沥青质加氢过程的影响

以中低温煤焦油沥青质为原料,采用NiMoW/γ-Al_2O_3商业催化剂,在反应温度380℃、反应压力8 MPa和反应时间1.5 h条件下,分别在不同剂油质量比(1∶25、1∶20、1∶15、1∶10)条件下进行加氢实验,通过采用元素分析、FT-IR、XRD、~1H-NMR和XPS等分析表征手段,考察不同剂油质量比对中低温煤焦油沥青质加氢转化过程的影响。结果表明,随着剂油质量比的增加,沥青质转化率提高,加氢产物分布也发生大幅变化,沥青质和芳香分轻质化转化为饱和分。但随着剂油质量比的进一步提高,同时也发生了更多的裂化反应和缩合反应,剂油质量比在合适范围能够很好地起到加氢轻质化且抑制结焦的效果。     

一种基于FPGA的可变速率帧结构设计与实现

在简述V.35接口的基础上针对V.35接口速率可变的应用需求提出了一种速率可变的帧结构,该帧结构可支持N×64kb/s(3≤N≤32)速率,从而在V.35接口上实现了多种速率的低速业务传输.     

广州市郊填埋场附近蔬菜重金属检测与讨论

蔬菜是人们餐桌上必不可少的食物,重金属在受污染的自然环境中又无处不在,而蔬菜中的重金属含量尤其令人担忧。本文使用原子吸收分光光度法(石墨炉)和原子荧光分光光度法检测了广州市郊某垃圾填埋场附近所种植蔬菜中重金属含量。结果:抽样由2013年10月至2014年9月共持续一年,共抽样检测12次,按平均每个月一次的频率,检测结果并未发现有蔬菜超出国家规定的限量值。     

Recent progress of the gas diffusion layer in proton exchange membrane fuel cells: Material and structure designs of microporous layer

Proton exchange membrane fuel cells (PEMFCs) have become the most attractive power supply units for stationary and mobile applications. The operation, design characteristics, as well as performance of PEMFCs, are closely related to the multiphase transport of mass, heat, and electricity in the cell, a critical of which is the gas diffusion layer (GDL). It is very important to guarantee the transmission of water and gasses under high current density, and which is the weakness of PEMFCs at present. Microporous layer (MPL) is considered to be the key variable for mass transfer, so varieties of works focus on modification of MPL materials and its structure design. However, there is still a lack of special review to summarize and prospect the progress of MPL in recent years. This review article therefore focuses on the insights and comprehensive understanding of four critical issues of the MPL, the porosity, pore size distribution, wettability, structural design and the durability of MPL. At last, the conclusion and recommendations section summarized the future prospects and recommendations for possible research opportunities.     

A practical reliability assessment approach and its application for pile-stabilized slopes using FORM and support vector machine

Bulletin of Engineering Geology and the Environment - Many uncertainties exist in pile-stabilized slopes which make their design substantially complicated. In this paper, a first-order reliability...     

川北某黑色页岩型铼矿工艺矿物学研究

通过矿相显微镜、扫描电镜、电子探针、X射线能谱元素面分析等多种手段综合研究了川北某黑色页岩型铼矿中铼的赋存状态。样品为黑色页岩,有机碳含量较高。粘土矿物总量为14.6%,黄铁矿含量16.2%,石英含量37.7%。样品具典型的粘土结构,矿物粒度微细。铼有两种赋存状态,一种呈类质同象形式赋存于黄铁矿内,另一种则以分散形式存在。典型黄铁矿测点Re平均含量为0.024%。黄铁矿是Re的重要载体矿物。建议通过浮选分离黄铁矿,从而实现Re的富集。      

亮色系建筑涂料色浆的研制及应用

阐述了自制亮色系色浆的必要性。介绍了自制亮色系色浆的颜料筛选,配方调整及其在建筑涂料中应用后对面漆性能的影响。     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

优化作业方式提高始极片质量

针对某厂铜电解种板工序存在的始极片质量波动较大的问题,从种板系统体积控制和添加剂匹配的角度出发,分析各种因素对始极片质量的影响,做出了相应的改进措施,使种板系统运行更加稳定,始极片质量得到进一步提升。